
PRODUCTS
EOP 8E1 to 4Ethernet Converter
Humanity EOP HM-C800B 8E1 to 4Ethernet converter realizes Ethernet transmission over 1~8E1. This model adopts with new international protocol (G.7041、G.7042、G.7043、G.8040) at all layers and able to intercommunicate with third party device followed same standard.
Main Feature:
-
Support auto delete the fault E1 channels (BER more than 1E-6 or a serious warning LOS/AIS/LOF or the signal loop back); Auto-restore the use of E1 after eliminate the failure.
-
For 8E1 channels, the maximum tolerable time delay difference between any two can be up to 220ms. It will have an alarm for exceed the limit when the time delay difference over 220ms, meanwhile, business interrupt jitter tolerance, jitter transfer characteristics in the line with ITU-T G.823.
-
E1 automatic test loop back and cut off function. The E1 channel will be cut off once find E1 signal loop back. Auto-restore the use of E1 after release. Avoid the network storm without interrupting operations.
-
Support local E1 channel loop, facilitate to test E1 channels
-
Ethernet data will not be damaged if enlarge or reduce the transmission bandwidth by means of network management.
Technical Parameters
E1 interface |
E1: 8 E1 channel |
According to ITU-T G.703 |
|
Line code: HDB3 |
|
Velocity: 2.048Mbit/s ± 50ppm |
|
Impedance: 75Ω unbalanced or 120Ω balanced optional |
|
Jitter index: comply with ITU-TG.823 standard |
|
Connector: BNC or RJ45 optional. DB37 with device and able to be with 8 RJ45(120Ω) or 16 BNC(75Ω) by 2pcs adaptor |
|
Ethernet interface |
4 Ethernet with VLAN |
Connector: RJ-45 |
|
VLAN control by DIP SEL4 switch |
|
According to IEEE 802.3 Recommendation |
|
Comply with IEEE802.1Q |
|
Auto adapt 10/100M, full/half duplex |
|
Auto support flow control(back press control in half duplex and pause flow control in full duplex) |
|
MAC address table capability: 1024 |
|
MAC address table aging time: 5 minutes |
|
Minimum frame length: 64 bytes |
|
Maximum frame length: 1916 bytes |
|
Indicator light |
POWER1 and POWER2: power indicator light for AC and DC |
LINK1~4: for 1~4 Ethernet connection status |
|
ALR: general alarm. Indicates there is alarm. |
|
L1~L8: indicates 1~8 E1 alarm. |
|
DIP SEL1,2=OFF, OFF. L1~L8 indicates LOS |
|
DIP SEL1,2=ON, ON. L1~L8 indicates AIS |
|
DIP SEL1,2=ON, OFF. L1~L8 indicates LOOP |
|
DIP SEL1,2=OFF,ON. L1~L8 indicates LOF |
|
Management (please state in order) |
RS232 interface for hyper terminal network management |
SNMP network management optional |
|
Default with RS232 hyper terminal NMS |
|
Power supply |
AC and DC dual powerwith redundancy |
Power consumption: less than 10W |
|
Environment |
Operating temperature: -5℃~50℃ |
Relative humidity: 0%~95%, non-condensing |
Typical Application Diagram
Contact Us
Address: East Anningzhuang Rd.,Haidian District, Beijing, China
Tel: +86-10-62924922/62926577
Fax: +86-10-62922921
E-mail: human@hm-it.com
Copyright@ Beijing Human Information Technology Co., Ltd 京ICP备13001393号-1 SEO label

Scan to focus wechat

Scan to view mobile website